CanExel and engineered wood siding in Moncton

Engineered wood gives a house the look of painted wood boards, without the scraping and repainting cedar clapboard asks for.

Engineered wood siding costs about $7.20 to $18.00 per square foot installed in Canada (HomeStars lists CanExel at $7.20 to $12.00 and engineered wood at $12.00 to $18.00). CanExel typically lasts around 30 years.

This page covers engineered wood siding: CanExel, LP SmartSide and similar prefinished boards. For natural wood, see cedar shingle siding. To compare every material by price, see the cost guide.

What engineered wood siding is

Engineered wood siding is made from wood strands or fibres bound with resins and pressed into boards and panels. RenoQuotes notes that the resins and zinc borate in it are there to cut down water absorption and resist decay. The boards come primed or fully prefinished in the factory, with an embossed grain on the face.

From the street it reads as painted wood: crisp lap boards, deep shadow lines and a flat matte finish. Up close it’s lighter and more consistent than real wood, with no knots to bleed through the paint.

Two names come up most around Moncton:

  • CanExel. A prefinished wood fibre siding sold widely in Atlantic Canada and Quebec, in lap and panel styles and a range of factory colours. HomeStars lists it separately at $7.20 to $12.00 per square foot installed, with a typical life of about 30 years.
  • LP SmartSide. Made by LP (Louisiana-Pacific), in lap, panel and trim. It can be bought primed and painted on site, or prefinished.
House front with dark green vertical board and batten siding, a shingled gable and a covered porch
Board and batten on the walls, shingles in the gable: two profiles on one house. Photo: Robert Neustadter, Wikimedia Commons, CC BY-SA 4.0.

Engineered wood or vinyl?

Engineered woodVinyl
LookPainted wood, deep shadow linesThinner profile, visible panel overlaps
Installed cost (HomeStars)$7.20 to $18.00 / sq ft$4.80 to $11.50 / sq ft
ImpactStiff, holds up to knocksStandard panels crack more easily in deep cold
UpkeepSeal cut edges, touch up scrapes, repaint eventuallyWash now and then, never paint

If the budget allows and you want a house that looks like it has real wood boards, engineered wood is the step up. If you want the lowest upkeep for the money, vinyl still wins.

What makes or breaks an engineered wood job

Engineered wood is durable, but it’s still wood fibre. It stays sound as long as water can’t soak into it. Almost every failure comes back to installation:

Every cut end sealed

The factory finish protects the face and the edges it left. Every cut a crew makes on site exposes raw fibre, and the makers' instructions call for those ends to be sealed or painted before the board goes up.

Clearance from roofs, decks and the ground

Boards need a gap above shingles where a wall meets a roof, above decks, and above grade, so they’re not sitting in snow and splashback. In a Moncton winter, where snow can pile against a wall for weeks, that clearance matters.

A drainage gap behind it

Strapping over the house wrap lets water that gets behind the boards drain out and lets the back of the boards dry. RenoQuotes calls a rainscreen gap like this best practice for siding across Canada.

Fasteners and flashing as specified

Nails go in at the spacing and depth the maker calls for, with joints flashed behind. Overdriven nails break the surface and let water in. Kickout flashing where a roof meets a wall keeps rainwater off the boards below.

Thinking about CanExel or SmartSide for your house?

Call (506) 405-9905

Engineered wood in Greater Moncton

Engineered wood suits the houses people most often want a wood look on: newer builds with a board-and-batten front, plain two-storeys where a deep lap shadow line adds character, and older houses in Moncton, Dieppe and Riverview that were first clad in wood clapboard.

It handles impacts well, which matters for houses where snow gets plowed toward the wall or kids play against it. The thing to watch is snow and ice sitting against the bottom courses. Keeping the right clearance at grade and over lower roofs, and good eavestroughs that keep meltwater off the wall, add years to it. See soffit, fascia and eavestroughs.

Looking after it

  • Wash it once a year with a garden hose and a soft brush. No pressure washer close up; it can drive water into joints.
  • Touch up scrapes and chips with the maker’s matching paint before winter.
  • Keep plants, firewood and snowbanks off the bottom courses where you can.
  • Check caulked joints around windows and trim every few years.

Prefinished boards hold their colour for years, but every painted finish eventually fades. When it does, engineered wood can be repainted.

Cost

HomeStars puts CanExel at $7.20 to $12.00 and engineered wood more broadly at $12.00 to $18.00 per square foot installed. RenoQuotes' 2026 guide gives $17 to $23 for engineered wood such as LP SmartSide and CanExel. Price guides disagree, which is why a measured quote for your house is the number to trust. The cost guide lays out what drives it.

Thinking about new siding? Start with a free look.

Call to describe the house, or send the form and we call you back. Quotes are free and written.

(506) 405-9905
  • A free visit to measure and look at what’s under the old siding
  • A written quote that lists removal, wrap, trim and disposal
  • Moncton, Dieppe, Riverview, Shediac and the villages around them

Or send the details

Tell us about the house. We call back to talk it through and book a free visit.

We only use your details to reply about your house. See the privacy note.

Call now Free quote